Sri Sresti Marketing Solutions
srisms_magnet021044.jpg srisms_magnet021042.jpg srisms_magnet021025.jpg srisms_magnet021024.jpg srisms_magnet021023.jpg srisms_magnet021022.jpg srisms_magnet021021.jpg srisms_magnet021020.jpg srisms_magnet021019.jpg srisms_magnet021018.jpg srisms_magnet021017.jpg srisms_magnet021016.jpg srisms_magnet021015.jpg srisms_magnet021014.jpg srisms_magnet021013.jpg srisms_magnet021012.jpg srisms_magnet021011.jpg srisms_magnet021010.jpg srisms_magnet021009.jpg srisms_magnet021007.jpg srisms_magnet021005.jpg srisms_magnet021004.gif
Sri Sresti Marketing Solutions
Mobile: (+91) 92471 10759 / 90141 10759
Email: srisms.com@gmail.com

Lead Acid Battery Charger with Pulsar

Now you can restore partially weak or totally worn out / dead batteries with Srisms battery rejuvenator products. At present these are tested and recommended for inverter batteries up to 200Ah.

Srisms – Battery Charger with Pulsar – Special charger to charge battery

This is not useful if there is any short circuit in the battery or the plate’s separator is totally worn out or the battery is grown in size or over charged.

Srisms battery charger is designed to charge poor-functional batteries or batteries which have lost their rated capacity. In this condition even exchange rate is too less. This is a12V rated one and is to be used only for 12V rated lead acid batteries only. It is better to use Srisms battery liquid along with Srisms pulsar with charger to charge the battery. In this way the battery rejuvenates at a quicker pace and the charge stays long. Since this is 12V 5amp rated one and takes about 20hours (approx) to fully charge a 100Ah battery-working battery (charging timing is not constant for each battery due to various conditions). This is useful for slow charging only.

 The indicators on the right side of the Pulsar unit has two LED’s (Red  LED – for low battery – glows when voltage of the battery is less than 10.V and Green LED – for battery full – glows when voltage of the battery is more than 13.7V). However both will glow when no battery is connected and the unit is connected to power. After connecting to power and battery only the specified LED will glow or indicate the status of the battery. On the left side only one indicator glows – showing the status of the pulsar. However this will go dim if it is connected to battery of higher rating above 5amps or if the battery is also connected with another charger / inverter.

 Results will vary largely depending upon the function of the battery and other issues. In most conditions results will come only after a two weeks or so. This is a slow acting principle and will not give you instant results. Can be used for newer batteries also but you will not know the results of the pulsar hence recommended to be used when you find the capacity / back-up time of the inverter has come down. This generally happens after the warranty period. However these conditions may change due to many factors.

This is useful for batteries in vehicles, trucks, fork lift vehicles, inverter batteries, emergency vehicles, boats etc where ever there is regular charging of lead acid batteries.This is one answer for common questions like:

How to revive a dead battery, how to bring a low efficiency battery to life again, how to rejuvenate a battery, how to make a dead lead acid battery come alive again, bring back to life, making battery to work for you more, how to improve the life of a battery, how to improve the efficiency the battery, how to prolong the life of lead acid battery, how to recharge a battery,

Technical  Specifications of SriSMS Battery Charger with Pulsar

Ø  Proven Technology Fly back CVCC-PWM Control.

Ø  Very Compact Size/ Light Weight.

Ø  Wide Input Range / highly efficient.

Ø  Output over Load, Short circuit Protection

Ø All double rated component used in product for reliability and long life.

 

Special Features:

Ø  Soft start on DC side.

Ø Filter circuit to limit ripple.

Ø  Charger current limiting

Ø  Automatic voltage regulation using digital control logic.


Input

Ø  Input Voltage: 150V AC TO 270V AC

Ø  Frequency: 47 TO 63 HZ.

Ø  Input Protection: Soft Start.

Ø  Inrush Protection: NTC.

Ø  EMI Compliance: Inbuilt RFI/EMI Filter Provided.

Ø  Efficiency: > 75-85%.

 

Output

Ø  Voltage: 13.7VDC

Ø  Current: 5 A

Ø  Regulation: ± 2% Line and Load.

Ø  Ripple: < 1% PK-PK.

Ø  Protection: O/P Over load & Short Circuit.


Cooling

Ø  Natural cooling.


Isolation

Ø  I/P TO O/P: 1.5 KV AC for One minute.

Ø  O/P TO Earth: 1.5 KVAC for one minute.

 NOTE: The pulsar can bring interference to other type of electronic circuits or gadgets, hence keep away any other electronic goods while operating / charging the battery with this unit

 

Srisms Battery Liquid- liquid to enhance the battery chemistry

 

Advantages of using Battery Liquid for all lead acid batteries. Best suitable for inverter batteries.

1.      Increases battery life

2.       Battery charges faster

3.       Longer discharge from battery

4.       Decreases battery cyclic change

5.       Improves return on investment

6.       More back time from battery

 

Always use Battery Pulsar along with Battery Liquid for best and prolonged results

 

Follow these instructions:

1.       Battery Liquid should not be used for very new batteries (below one year of age). You can use after twelve  months of first use (installation) and there after every year

2.       Battery Liquid  should not be used for more than once a year if the battery capacity is not lost more than 60% at the time of using Battery Liquid

3.       Battery Liquid would not be useful if there is any short circuit in the battery or the plate’s separator is totally worn out or the battery is grown in size or over charged.

4.       Best suitable for inverter batteries

5.      Maximum Ah capacity where Battery Liquid is useful is 200Ah

6.       Battery Liquid should not be mixed with any other liquid / additive / oil etc and used.

7.       While using Battery Liquid extreme caution should be taken. See that the liquid does not come into contact with eyes, skin and other sensitive parts of body

8.      Results would generally show up only after two to three weeks of application for semi functioning batteries.

9.      Optimum working temperature of a battery is around +27 degrees Centigrade. Results may vary if the working temperature of the battery and the climate is different.

10.   For totally dead batteries results will take a longer time

11.   Use Srisms Battery Charger / Solar Battery charger for restoring a dead battery

12.   Pour 50ml of Battery Liquid (one pack) in each cell of the battery. A 150Ah battery generally has 6 cells and requires 6 bottles of Battery Liquid

13.   For motor cycle batteries one bottle is enough for all the six cells.

14.   Though you use Battery Liquid initially unless you use Battery Pulsar results will not stay long

15.   If the water / electrolyte in the battery is full, empty or take out some of it, pour Battery Liquid and then fill up the remaining volume with water / electrolyte

16.    

 

 

Application: To be used for lead acid batteries only. Do not use for very new batteries & more than once a year. Recommended to use after the warranty period of the battery is over. Pour 50ml of Battery Liquid in each cell for larger batteries (like 100Ah / 135Ah / 150Ah inverter batteries). A 150Ah battery will have 6 cells & requires 6 bottles of Battery Liquid. Take all standard safety precautions while applying. Refer to an experienced person if necessary. Refer website www.srisms.com for application procedure. Each 50ml bottle is not be loose sold.

 

Srisms – Battery Pulsar – Electronics to enhance the electrical capacity of the battery

Srisms Battery Pulsar is a specially designed electronic gadget to improve the function of the overall electrochemical reaction along with some chemistry of the battery. Designed to give optimum results for inverter batteries that are already in use or running. Can also be used for isolated / worn out / dead batteries along with Srisms Battery Liquid along with Srisms battery charger. This is designed to be used for 12V batteries only with amp rating upto 200Ah.

 

This is useful for batteries in vehicles, trucks, fork lift vehicles, inverter batteries, emergency vehicles, boats etc where ever there is regular charging of lead acid batteries. Please note that Srisms battery pulsar is not a charger to charge the battery but it’s a device which helps in reconditioning the battery. Can also be used for other types of batteries like hybrid , gel cell, antimony, calcium plate designs and absorbed glass mat varieties.

 

 Installing the Srisms battery pulsar is very simple. Just fix the red wire of the pulsar to the red (+ve) terminal of the battery (hence the positive terminal has two wires, one from pulsar and another from inverter). Like wise fix the blue wire too. Once fixed correctly the LED indicator on the pulsar will start to glow that the connections are correct and functioning well. Take optimum precaution in fixing the pulsar as you are playing with a high current module. Wear protective wear and insulated material from all types of dangers of electricity. Refer to an experienced person if necessary for installation.

 

Srisms Battery Pulsar is a self driven device that will consume about 20mA of power to improve the function of the battery (while the inverter / charger is connected and running). it has been tested successfully in reconditioning / rejuvenating some dead batteries to the extent of 60% of their rated capacity in about 3 months time Using Srisms battery Pulsar, Srisms Battery Liquid and along with Srisms Battery Charger  Its like bringing back the dead alive.

 

Results will vary largely depending upon the function of the battery and other issues. In most conditions results will come only after a month or so. This is a slow acting principle and will not give you instant results. Can be used for newer batteries also but you will not know the results of the pulsar hence recommended to be used when you find the capacity / back-up time of the inverter has come down. This generally happens after the warranty period. However these conditions may change due to many factors.

 

Srisms – Battery Charger – Special charger to charge battery

 

Srisms battery charger is designed to charge non-functional batteries or batteries which lost their rated capacity. This is a12V rated one and is to be used only for 12V rated lead acid batteries only. It is better to use Srisms battery liquid along with Srisms pulsar to charge the battery. In this way the battery rejuvenates at a quicker pace and the charge stays long. This is 12V 2amp rated one and takes about 50hours to charge a 100Ah battery. This is useful for trickle / slow charging only.

 

 

Srisms – Solar Battery Charger – Solar powered battery charger to prevent deep discharge

 

Srisms solar battery charger is useful to contain the deep discharge of car batteries that are left unatteneded for longer time. Whle a car is left unused for a longer time the battery voltage comes / falls / reduces and thus while starting the battery cannot the engine to start. The main reason is the battery self discharge. To prevent the battery loosing its charge this Srisms solar battery charger comes in hand.

 

Srisms solar battery charger is powered with a powerful 12V 4000mW solar module and a charge controller for proper charging of the battery.

 

Srisms Battery Life Saver Kit - Contains Battery Pulsar and Battery Liquid (6bot)

 

Battery rejuvenator, battery life enhancer, battery booster, battery charger, battery additive, how to bring back dead battery alive, getting more from the battery, how to restore a dead battery, how to charge a lead acid battery, how to revive a non working battery

 

  

 

How to revive a dead battery, how to bring a low efficiency battery to life again, how to rejuvenate a battery, how to make a dead lead acid battery come live again, bring back to life, making battery to work for you more, how to improve the life of a battery, how to improve the efficiency the battery, how to prolong the life of lead acid battery, how to recharge a battery,

 

 

srisms_magnet021003.jpg

Lead Acid Battery Pulsar
Srisms – Lead Acid Battery Life Enhancer / Rejuvenator / Re-conditioner / Saver

This is not useful if there is any short circuit in the battery or the plate’s separator is totally worn out or the battery is grown in size or over charged.

The battery voltage should be minimum 11V at the time of connecting the Pulsar (maintained for a week)

Srisms battery pulsar is designed to recondition / rejuvenate poor-functional battery or batteries which have lost their rated capacity. In this condition even exchange rate is too less. This is a12V rated one and is to be used only for 12V rated lead acid batteries only. It is better to use Srisms battery liquid along with Srisms pulsar with charger to charge the battery. In this way the battery rejuvenates at a quicker pace and the charge stays long. This is slow process and usually takes about 3 to 4 months to recondition / rejuvenate / save the battery.

Results will vary largely depending upon the function of the battery and other issues. In most conditions results will start only after two months or so. This is a slow acting principle and will not give you instant results. Not recommended to be used for newer batteries as you will not know the results of the pulsar hence recommended to be used when you find the capacity / back-up time of the inverter battery has come down or the car battery is unable to start the engine. This generally happens after the warranty period. However these conditions may change due to many factors.

This is useful for batteries in two wheeler and four wheeler vehicles, trucks, fork lift vehicles, inverter batteries, emergency vehicles, boats etc where ever there is regular charging of lead acid batteries. This is one answer for common questions like:  How to revive a dead battery, how to bring a low efficiency battery to life again, how to rejuvenate a battery, how to make a dead lead acid battery come alive again, bring back to life, making battery to work for you more, how to improve the life of a battery, how to improve the efficiency the battery, how to prolong the life of lead acid battery, how to recharge a battery,

Technical  Specification of SriSMS Battery Pulsar

Operating frequency: 1.8 to 3.6Mhz approx.

Burst ringing voltage: From 50-60volts @ about 40amps for 20micro seconds @ 2000times / sec

 

NOTE: The pulsar can bring interference to other type of electronic circuits or gadgets, hence keep away any other electronic goods while operating / charging the battery with this unit

 

Important: Due to constant upgrades there might be slight variations in technical parameters and other specifications that are subjected to change without notice.

Now you can restore partially weak or low back up giving batteries  with Srisms battery rejuvenator products. At present these are tested and recommended for inverter and car batteries upto 200Ah.

 

Srisms – Battery Pulsar – Electronics to enhance the electrical capacity of the battery

Srisms – Battery Charger– Electronics to re-charge the battery

Srisms – Solar Battery Charger – Solar powered battery charger to prevent deep discharge

 

 

Sri SMS Lead Acid Battery Charger

This is not useful if there is any short circuit in the battery or the plate’s separator is totally worn out or the battery is grown in size or over charged.

Srisms battery charger is designed to charge battery which has lost their rated voltage or charge. This is a12V rated one and is to be used only for 12V rated lead acid batteries only. It is better to use Srisms battery liquid along with Srisms pulsar with charger to charge the battery. In this way the battery rejuvenates at a quicker pace and the charge stays long. This is slow process (5amps charging) and usually takes about 1 to 2 months to charge a battery.

This is useful for batteries in two wheeler and four wheeler vehicles, trucks, fork lift vehicles, inverter batteries, emergency vehicles, boats etc where ever there is regular charging of lead acid batteries.

 Technical Specifications of SriSMS Battery Charger

Ø Proven Technology Fly back CVCC-PWM Control.

Ø  Very Compact Size/ Light Weight.

Ø  Wide Input Range / highly efficient.

Ø  Output over Load, Short circuit Protection

Ø  All double rated component used in product for reliability and long life.

 

Special Features:

Ø  Soft start on DC side.

Ø  Filter circuit to limit ripple.

Ø  Charger current limiting

Ø Automatic voltage regulation using digital control logic.


Input

Ø  Input Voltage: 150V AC TO 270V AC

Ø  Frequency: 47 TO 63 HZ.

Ø  Input Protection: Soft Start.

Ø  Inrush Protection: NTC.

Ø  EMI Compliance: Inbuilt RFI/EMI Filter Provided.

Ø  Efficiency: > 75-85%.

 

Output

Ø  Voltage: 13.7VDC

Ø  Current: 5 A

Ø  Regulation: ± 2% Line and Load.

Ø Ripple: < 1% PK-PK.

Ø  Protection: O/P Over load & Short Circuit.


Cooling

Ø  Natural cooling.


Isolation

Ø  I/P TO O/P: 1.5 KV AC for One minute.

Ø  O/P TO Earth: 1.5 KVAC for one minute.

 

Important: Due to constant upgrades there might be slight variations in technical parameters and other specifications that are subjected to change without notice.

 

Take all standard precautions while charging / handling batteries.